عجلة مشط التبن 723-47-16103 لـ حفارة متوسطة الحجم Komatsu PC300-6





إذا قررت شراء المعدات بسعر منخفض، فتأكد أنك تتواصل مع البائع الحقيقي. اكتشف أكبر قدر ممكن من المعلومات عن مالك المعدات. تتمثل إحدى طرق الغش في تقديم نفسك كشركة حقيقية. إن ساورك شك، أخبرنا عن ذلك من أجل تشديد الرقابة وذلك من خلال نموذج التعليقات.
قبل أن تقرر القيام بالشراء، احرص على مراجعة العديد من عروض البيع بعناية لفهم متوسط تكلفة المعدات التي اخترتها. إذا كان سعر العرض الذي أعجبك أقل بكثير من عروض مشابهة، ففكر في الأمر بتأنٍ. قد يكون هناك فرق أسعار هائل يشير إلى عيوب مخفية أو أن البائع يحاول ارتكاب أعمال احتيالية.
ابتعد عن شراء المنتجات التي يكون سعرها مختلف بشدة عن متوسط السعر لمعدات مشابهة.
لا توافق على الوعود المثيرة للشكوك والبضائع المدفوعة مسبقًا. إن ساورك شك، فلا تخاف من طلب توضيح التفاصيل وأن تطلب صورًا ومستندات إضافية للمعدات وأن تفحص صحة التصديق على تلك المستندات وتطرح الأسئلة التي تساورك.
أكثر أنواع الاحتيال شيوعًا، قد يطلب البائعون غير المنصفون مبلغًا معينًا كعربون مسبق "لتحجز" حقك في شراء المعدات. وبالتالي يستطيع المحتالون تجميع مبلغًا ضخمًا ثم يختفون ولا تستطيع التواصل معهم بعد ذلك.
- إرسال الدفعة المسبقة إلى البطاقة
- لا تقم بالدفع المسبق بدون مستندات ورقية تؤكد عملية تحويل الأمول إذا ساورك أي شك في البائع خلال التواصل.
- إرسال إلى حساب "الوصي" “Trustee”
- هذا الطلب ينبغي أن يكون بمثابه إنذار فأنت على الأرجح تتواصل مع شخص محتال.
- إرسال إلى حساب الشركة باسم مشابه
- توخّ الحذر، فقد يختفي المحتالون أنفسهم أيضًا خلف شركات معلومة أو يدخلون تغييرات طفيفة على الاسم. لا تحول الأموال إذا ساورك شك في اسم الشركة.
- استبدال البيانات الخاصة في فاتورة شركة حقيقية
- قبل التحويل، تأكد أن البيانات المحددة صحيحة وأنها ترتبط أو لا ترتبط بالشركة المحددة.
معلومات الاتصال بالبائع







Product Overview
Fuel is the largest running cost on a 30‑ton excavator, and owners watch litres per hour closely. What that number does not show is litres per cubic metre. A machine burning the same fuel but moving less material is getting more expensive every shift, and the usual suspects — engine condition, operator technique, ground conditions — are checked first. The hydraulic block is rarely on the list, even though leakage makes the engine work harder for the same output by converting pressure into heat instead of movement.
The PC300‑6 uses this hydraulic main valve — references 723‑47‑16103, 723‑47‑16102 and 723‑47‑16101 cover the family — to divide pump flow among boom, arm, bucket, swing, travel and auxiliary. Once spools and bores wear, the pattern appears: the boom sags on a held bucket, the arm loses bite at the bottom of a cut, swing lands short, travel bogs under load. This OEM‑grade assembly replaces the block complete with fresh internals set to ‑6 values, so the worn unit comes off and the replacement fits the original port positions.
Core Advantages
1. Cuts fuel per cubic metre, not just fuel per hour
Restored pressure means less engine effort for the same material moved, which is the number that actually appears in the cost sheet.
2. Throttle settings fall back toward normal
Operators compensate for soft hydraulics with engine speed. Once the block holds pressure, the same output arrives at a lower setting.
3. Force returns at the cutting edge
Renewed spools put pressure back into the arm and bucket, so the machine digs instead of labouring.
4. Loads hold through the truck cycle
A sagging boom forces a re‑spot every pass. Restored retention keeps the bucket where it was placed.
5. Complete assembly across the reference family
We confirm which of the three references your machine carries from its tag and serial, so the block matches rather than approximates.
Manufacturing & Quality Control
Spool and bore pairs are machined to print tolerance, matched by size, and hand‑run‑in until full‑stroke movement is smooth without binding. Assembled blocks are flow‑tested circuit by circuit with relief and compensator values logged against ‑6 figures; out‑of‑window units are stripped and corrected. Blocks ship internally oil‑fogged, ports capped, and crated on foam.
Frequently Asked Questions
Q1: How do I confirm which of the three references my machine uses?
A: Send a photo of the tag on the existing valve plus the machine serial number. The references belong to the same family but serve different builds.
Q2: Is rising fuel consumption really a valve symptom?
A: It can be. Internal leakage raises the engine's workload for unchanged output. Compare litres per hour against production, not in isolation.
Q3: What other symptoms indicate valve wear?
A: Boom drift on held loads, lost arm force, inconsistent swing, and travel that reacts to bucket load.
Q4: Can my existing block be rebuilt?
A: If the casting is sound and has never been rebuilt, a kit may restore it. Where several circuits leak, a complete assembly usually gives better service per dollar. Photos help us judge.
Q5: What hydraulic servicing accompanies installation?
A: Flush the system, renew the return filter, clean the suction strainer, and refill with specified oil. Contaminated oil damages new clearances quickly.
Q6: What is excluded from warranty?
A: Material and assembly faults are covered. Damage from dirty oil, water ingress, a spool forced against a bind, or reliefs altered outside specification is not. Photograph the crate before opening if damage is visible.